一、入水、浇口：gate 进入位： gate location
水口形式：gate type 大水口：edge gate /sprue gate
细水口/点浇口： pin-point gate 水口大小：gate size
转水口： switching runner/gate 唧嘴口径:sprue diameter
二、流道: runner 热流道:hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate
圆形流道：round(full/half runner 流道电脑分析：mold flow analysis
流道平衡:runner balance 热嘴： hot sprue
热流道板：hot manifold 发热管：cartridge heater
探针: thermocouples 插头:connector plug
插座： connector socket 密封/封料:seal
三、运水：water line 喉塞：line lpug
喉管：tube 塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件： mold components
二板模：2-plate mold 三板模：3-plate mold
边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing
中托司：shoulder guide bushing 中托边L：guide pin
顶针板：ejector retainner plate 托板： support plate
螺丝： screw 管钉：dowel pin
开模槽：ply bar scot 内模管位：core/cavity inter-lock
顶针： ejector pin 司筒：ejector sleeve
司筒针：ejector pin 推板：stripper plate
缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter 模胚（架）： mold base
上内模：cavity insert 下内模：core insert
行位（滑块):slide 镶件：insert
压座/斜鸡：wedge 耐磨板/油板：wedge wear plate
压条：plate 撑头: support pillar
唧嘴： sprue bushing 挡板：stop plate
定位圈：locating ring 锁扣：latch
扣鸡：parting lock set 推杆：push bar
栓打螺丝：S.H.S.B 顶板：eracuretun
活动臂：lever arm 分流锥：spure sperader
水口司:bush 垃圾钉：stop pin
隔片：buffle 弹弓柱：spring rod
弹弓:die spring 中托司：ejector guide bush
中托边：ejector guide pin 镶针：pin
销子：dowel pin 波子弹弓：ball catch
喉塞: pipe plug 锁模块：lock plate
斜顶：angle from pin 斜顶杆：angle ejector rod
尼龙拉勾：parting locks 复位键、提前回杆：early return bar
水口形式：gate type 大水口：edge gate /sprue gate
细水口/点浇口： pin-point gate 水口大小：gate size
转水口： switching runner/gate 唧嘴口径:sprue diameter
二、流道: runner 热流道:hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate
圆形流道：round(full/half runner 流道电脑分析：mold flow analysis
流道平衡:runner balance 热嘴： hot sprue
热流道板：hot manifold 发热管：cartridge heater
探针: thermocouples 插头:connector plug
插座： connector socket 密封/封料:seal
三、运水：water line 喉塞：line lpug
喉管：tube 塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件： mold components
二板模：2-plate mold 三板模：3-plate mold
边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing
中托司：shoulder guide bushing 中托边L：guide pin
顶针板：ejector retainner plate 托板： support plate
螺丝： screw 管钉：dowel pin
开模槽：ply bar scot 内模管位：core/cavity inter-lock
顶针： ejector pin 司筒：ejector sleeve
司筒针：ejector pin 推板：stripper plate
缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter 模胚（架）： mold base
上内模：cavity insert 下内模：core insert
行位（滑块):slide 镶件：insert
压座/斜鸡：wedge 耐磨板/油板：wedge wear plate
压条：plate 撑头: support pillar
唧嘴： sprue bushing 挡板：stop plate
定位圈：locating ring 锁扣：latch
扣鸡：parting lock set 推杆：push bar
栓打螺丝：S.H.S.B 顶板：eracuretun
活动臂：lever arm 分流锥：spure sperader
水口司:bush 垃圾钉：stop pin
隔片：buffle 弹弓柱：spring rod
弹弓:die spring 中托司：ejector guide bush
中托边：ejector guide pin 镶针：pin
销子：dowel pin 波子弹弓：ball catch
喉塞: pipe plug 锁模块：lock plate
斜顶：angle from pin 斜顶杆：angle ejector rod
尼龙拉勾：parting locks 复位键、提前回杆：early return bar
气阀：valves 模排气：parting line venting
斜导边：angle pin
承压平面平衡：parting surface support balance 回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水：water line interferes with ejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
反呵：reverse core 弹弓压缩量：spring compressed length
稳定性好：good stability,stable 强度不够：insufficient rigidity
均匀冷却：even cooling 扣模：sticking
热膨胀：thero expansion 公差：tolorance
铜公(电极）：copper electrode
斜导边：angle pin
承压平面平衡：parting surface support balance 回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水：water line interferes with ejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
反呵：reverse core 弹弓压缩量：spring compressed length
稳定性好：good stability,stable 强度不够：insufficient rigidity
均匀冷却：even cooling 扣模：sticking
热膨胀：thero expansion 公差：tolorance
铜公(电极）：copper electrode
没有评论:
发表评论